End devices

This is the final part of the installation, the end devices. These are either the things sending the impulses (Sensors like motion sensors, timers, etc.) or the once receiving impulses (Actuators like lights, speakers, etc.). By installing them to your paper UI, you can use them to make rules in vs-code.

TP link smart plug

Anker 2

In openhab, paperUI, add-ons, install the tp-link binding
Install the smart-plug through the TP link setup menu in your network
PaperUI will detect your smart plug
Your smart plug will show up in the inbox
Add your smart plug
Your smart plug will show up in the things directory
You can edit the name of the smart plug by pressing the pencil
Make an switch item by pressing the icon in front of the name
Your item will show up in the item directory
By pressing the pencil next to the item you can change the name of the item and add it to a group.

Anker 3

Philips Hue lights

Install the Hue bridge to connect the lamps to internet
Download the Philips Hue app
Add your lights by searching or by adding the serial number found on the lamp
In openhab, paperUI, add-ons, install the Hue binding
PaperUI will detect your bridge
Add bridge as a thing
Pair the bridge using the pairing button on the front panel of the bridge
Openhab detects your philips Hue lights
Add the lamp as a thing
Press the blue icon in from of the channel and link your channel to an item
label the item with the name of the location of your device.

Philips Hue sensor

Remove the transparent tag to activate the battery
press the setup button with a paperclip
The Hue app will find the sensor by itself
In openhab, paperUI, Inbox you will find the hue sensors (ambient light, motion and temperature)
Press the blue v and add the sensors as a thing

KNX

Anker 1

Download ETS software to program your KNX bus.
Set the bus adress of your IP gateway (example 1.1.11 through 1.1.16)
Set the adress of your actor
Set the bus adress of your input KNX device
Make group adresses of what you like to control
example first number the location in the building (first floor, ground floor, cellar)
example second number what you would like to control (lights, dvices etc)
example thirth number location of device (ceiling, table etc).
Group adres will be like 1/2/5
In openhab, paperUI, add-ons, install the KNX binding

https://www.openhab.org/addons/bindings/knx/

Install the KNX gateway by setting the ip adress of your KNX ip gateway.
Set IP connection type to tunnel
Set your local adress to the ip adress of the openhab Pi
KNX FT 1.2 interface is only for a serial connection to your KNX bus. You don't need to install this.
KNX device set the adress to the bus adress openhab can use and is allocated by your KNX gateway.
Now you can define your channels, by pressing channels
Set Channel type to how openhab controles the KNX group adress
Give a openhab name of the channel at channel-ID
Give a name for your device at label
Channel configuration, set the group address of the KNX device.
Press the blue icon in from of the channel and link your channel to an item
label the item with the name of the location of your device.

TIME controle

In openhab, paperUI, add-ons, install the NTP binding and the ASTRO binding
In the inbox you will find the local time, add as a thing.
In the inbox you will find local moon and local sun, add as a thing

Precense detection of your phone

In openhab, paperUI, add-ons, install the Network binding
Go to inbox, press the blue + button to add a device
press networkbindings
press add manually
Pingable networkdevices
fill in the ip adress of your phone
add the device

SONOS player

Anker 4

Download the Sonos app
Add speaker
follow the instruction on your screen
In openhab, paperUI, add-ons, install the SONOS binding
In the inbox you will find the connected Sonos devices
Add your sonos speaker as a thing
By pressing the pencil next to the item you can change the name of the item and add it to a group.